Home
 


How To Go About Replacing A Worn Out Oven Heating Element


 Electric oven and broiler elements are more often than not easier to test and replace than many people are aware of. Irrespective of the element you want to replace, the steps always seem to quite similar in most instances. the first thing you need to do is to identify the oven manufacturer, the oven model number or the part number on the element. Normally, the packaging on the new element will list the manufacturers, part numbers and model number for which it does serve as a replacement. It is highly recommended that you double check the numbers and ensure that they match. However, it is worth mentioning that not all oven malfunctions are brought about by faulty elements. If you realize that an oven element is not working, the first thing you need to do is to check if the range is receiving any power. In addition, you should never ignore the fusing system inside the range. 

Once you have the model number and the requisite number right, you should turn off the power to the oven at its breaker box. You should then unplug the oven then start working on the unit. Slowly, remove the screws that secure the element to the oven alternatively, you may have to pull the plugs that connect the element. Remove a retaining shield and then lift out the malfunctioning element. Pull the element 4 to 5 inches away from the back wall of the oven unit. Slowly and very carefully remove the wires joined to the prongs on the element, take your time to note the way the wires are attached, if in doubt, feel free to label the spots so as to be sure to attach the wires in a similar manner.

You can then proceed to install the new oven element, carefully attaching all the wires as they were previously attached and secure the new element to the back wall of the oven. Once this is done, simply plug the oven back in and then return the breaker unit to the ON position. You can then proceed to test the oven so as to find out if it is working as planned. Don’t get too concerned if you see some smoke emanating from the unit, this is most likely some factory coating melting off.

As a rule of thumb, it is always recommended that you go through the owner’s manual before you commence any form of repair. In addition to this, whenever you are in doubt about replacing any element in your oven, take the safe route and get a professional electrician do the work for you.

Here are some of the popular oven replacement heating elements. They include but are not limited to the following:

1) Product Name: GE Oven Coil Surface Element

Product Price: $ 25.10

Product URL: https://is.gd/xlPEnu

Product Details: this coil element is six inches in diameter. Most of the time, if the surface element doesn’t heat then the surface element or its switch is defective and must therefore be replaced. To clearly determine if the element is defective, you should use a multimeter to test the unit for continuity. The replacement does require some basic hand tools since some disassembly is required. Some repair experience will therefore be quite helpful.

2) Product Name: GE Oven Bake Element

Product Price: $ 16.48

Product URL: https://is.gd/ux3D4v

Product Details: this is an oven bake element with terminal that are basically male quarter inch spade connectors. They are usually quite durable and are also easy to install when compared against other similar elements. The wires usually push onto the heating elements connectors and are rather thick, making them easy to handle and fix. In the event that the oven doesn’t bake, then chances are that the element has burned out and therefore needs to be replaced. Some basic hand tools are required for fixing and some disassembly is also required. In addition, it would also be helpful if you have some repair experience.

3) Product Name: Oven Radiant Surface Element

Product Price: $90.69

Product URL: https://is.gd/zJfQet

Product Details: this is a relatively large radiant/haliant surface element with a 2000 Watt sensor. In the event that the surface element is not heating, then most likely the surface element is defective. You should use a multi-meter to test the element in question for continuity, if you find the element to be having continuity then element switch is defective and needs replacement. 



New York, Los Altos, Arizona, Rhode_Island, Ottawa, Alvin, Erlanger, Kenmore, Washington, Brainerd, Sioux City, Lenoir, New Philadelphia, Streetsboro, Goldsboro, Yuma, San Rafael, Medford, Wylie, Jennings, Warren, Macon, Port Washington, Georgetown, Louisiana, Danbury, Agawam, Ohio, South River, White Settlement, Galt, Fairmont, Rancho Mirage, Sweetwater, Platteville, West Monroe, Farmington, Escanaba, Lighthouse Point, Albertville, Chino, Stoughton, Plainfield, Oklahoma, Oak Lawn, Sauk Village, Carson, Kirksville, Minneapolis, Phillipsburg, Southern Pines, Bloomsburg, Missouri City, Beacon, Bedford, Laurel, Arkansas, Wisconsin, Seven Hills, Pleasantville, Sandy, Colorado, Villa Park, Rialto, Butte-Silver Bow (balance), Middleburg Heights, Greensburg, Barnstable Town, Lynbrook, Christiansburg, Greensburg, Keokuk, Tukwila, North Dakota, Oswego, St. George, Watertown, Artesia

delicious Digg Myspace StumbleUpon LinkedIn Technorati Facebook Meneame Twitter Reddit Google Sphinn Yahoo Buzz Mixx